Clifford Concept 650MkII Installationsanleitung

© 2007 Directed Electronics Vista, CA N919730P 01-07installation guideConcept 650MkII

www.directed.com8h1/7 blue/white (-) second unlock output (200mA)This wire produces a (-) 200mA output for vehicles with progressive/selective doorunl

© 2007 directed electronics9armed, this wire will trigger the system.h1/14 green (-) door trigger input - zone 4Most vehicles use negative door trigge

www.directed.com10cle has a positive switched interior light circuit, attach this wire to a 12 volt constant source.secondary harness wire connection

© 2007 directed electronics11* This feature is not evaluated by Thatcham.NNOOTTEE::The current handling capacity of each immobilisation circuit is 20

www.directed.com12The Black H4/3 wire is the input for the on-board dual make indicator light flashrelay. If the indicators are switched positive conn

© 2007 directed electronics13type A: positive-triggered, relay-driven systemThe system can control Type A door locks directly, with no additional part

www.directed.com14type B: negative-triggered, relay-driven systemThis system is common in many Toyotas, Nissans, Hondas and most European Fordvehicles

© 2007 directed electronics15type C: reversing polarity systemUse these instructions if the power door lock switch has four or five heavy-gaugewires.

www.directed.com16+ 12V FUSED7.5A /MOTOR15A(+) 12VMOTOR (+)UNLOCK WIREX CUT XX CUT XMOTOR (+)LOCK WIREH2/1H2/2H2/3H2/5H2/6H2/7GREEN/BLACKLOCK #30 COMM

© 2007 directed electronics17type D: after-market actuatorsVehicles without central door locking or with single-point central locking only requireaddi

Bitwriter®, Code Hopping®, Directed®, Doubleguard®, ESP®, FailSafe®, Ghost Switch®, Learn Routine™, Nite-Lite®,Nuisance Prevention®, NPC®, Revenger®,

www.directed.com18type F: one-wire systemType F door locks usually require a negative pulse to unlock and cutting the wire tolock the door. In some ve

© 2007 directed electronics19type G: positive (+) multiplexsingle-resistor typeIf one resistor is used in the door lock switch/key cylinder, the wire

www.directed.com20type H: negative (-) multiplexsingle-resistor typeIf one resistor is used in the door lock switch/key cylinder, the wire will pulse

1. Cut the output wire from the door lock switch/key cylinder in half. 2. Test with the meter from the switch side of the cut door lock switch/key cyl

www.directed.com22the siren downward to avoid moisture collecting.2. Run the cable from the 515U Self-Powered Siren through the firewall into the pas

© 2007 directed electronics23mounting the receiver/antennaNNOOTTEE:: Do not bundle excess cable as this will reduce the range.The receiver/antenna po

www.directed.com24sure you check for clearance prior to drilling the mounting hole.plain-view valet switch, 2-pin blue plugThe Valet/Program switch sh

© 2007 directed electronics25multiplex (MUX) sensor ‘T’ harness, 4-pin connectorred and black wiresThese wires supply 12 volts and ground to the senso

www.directed.com26Concept 650MkII507C (507M)

© 2007 directed electronics27tilt sensorThe 507C tilt sensor detects when the vehicle is being raised in an attempt to eitherremove the wheels/tires o

contentswhat is included . . . . . . . . . . . . . .3transmitter configurations . . . . . .4transmitter functions . . . . . . . . . .4standard confi

www.directed.com28NNOOTTEE::Never place the sensor behind any metal brackets or under console pocketsthat will have coins or other metal objects in it

© 2007 directed electronics29Zones that are triggered at the time the system is armed are reported by an additional setof status chirps called Malfunc

www.directed.com30multiple event total recallThis will report the last eight system triggers.1. Press and hold of the PlainView 2 Valet switch.2. Whi

© 2007 directed electronics31* This feature is not evaluated by Thatcham.cliffnet wizard pro installation software programmingCliffnet Wizard Pro prov

www.directed.com32grid entry. Now program the features by entering the columns and rows asdescribed previously.) 3 chirps are always heard when enteri

© 2007 directed electronics33user selectable features descriptions - column oneadd new remote (only applicable with 5 button remote controls)zAuto-lea

www.directed.com34user selectable features descriptions - column twochange pin codezThis feature allows you to change the user's personal PIN cod

© 2007 directed electronics35user selectable features descriptions - column threeThe features in this column pertain to programming individual transmi

www.directed.com36zThe transmitter channel programmed into this feature will activate the accessoryoutput.clear all remoteszThis feature will erase al

© 2007 directed electronics37installer selectable featuresTo enter the Installer Selectable Features grid follow the instructions for the UserSelectab

www.directed.com2smart power up II . . . . . . . . . . . .44remote control sensor disable . .44mux (multiplex) sensors . . . . . . .45adjusting the

www.directed.com38unlock pulse single/doublezSingle: One door unlock pulse will be output when the system disarms.zDouble: Two door unlock pulses will

© 2007 directed electronics39installer selectable features descriptions - column twoaccessory output a programmingThe auxiliary accessory output wire

www.directed.com40accessory output b timer durationzStart Timer: Press the button; the siren will chirp to signal the start of thetimer duration sett

© 2007 directed electronics41horn output - pulsed/latchedzPulsed: H1/11 YELLOW/WHITE wire will generate a pulsing (-) output when thealarm is sounding

www.directed.com42zEnter the feature and press the button.zThe indicators will flash twice to confirm the engine RPM has been learned.NNOOTTEE::If on

© 2007 directed electronics43Note #4: PIN ProgrammingA PIN code can have one to four digits; each digit can be from 0-9. NNOOTTEE::A PIN code cannot b

www.directed.com44Note #5: Accessory ChannelszAll accessory channels can be programmed to different types of outputs includ-ing a pulsed output that d

© 2007 directed electronics45mux (multiplex) sensorsadjusting the 506T glass tamper sensorNOTE: Before testing, all the doors and windows must be shut

www.directed.com46loop is cut, then a 3-degree threshold is selected for normal sensitivity.AARRMMIINNGG DDEELLAAYYThe WHITE loop sets the amount of

© 2007 directed electronics47If the alarm exits adjustment mode automatically it will revert to its previous settings.To lock in the new settings, you

© 2007 directed electronics3what is includedzOne control module with 8-wire immob-zOne 18-pin main wiring harnessiliser harness and clamshellzTwo 5-bu

www.directed.com48adjusting the omnisensorWhile adjusting this sensor it is required that you strike the vehicle with the amountforce that is desired

© 2007 directed electronics497. Adjust Warn-away zonezPress .zSiren chirps 2 times.zSensor adjustment mode is entered.zHit vehicle at the desired leve

www.directed.com50blackjax* featureblackjax activation sequenceWhen BlackJax is programmed ON, BlackJax sequence will begin every time the igni-tion i

© 2007 directed electronics51blackjax* deactivation sequenceTo deactivate BlackJax* turn the key on and then enter the PIN code at any time.bypass bla

www.directed.com52certificate of installationAfter installation you must fill out the certificate of installation. Once you have filledout all informa

© 2007 directed electronics53

Immobiliser and Power/Ground Cable18-Pin Harness (H1)8-Pin Harness (H2)Smart Self-poweredSiren (Power)LED PortPlainView 2Valet Switch PortRF PortCliff

© 2007 directed electronics55H1 harnessWHITE - Light Flash 1 OutputVIOLET/BLACK Tachometer InputNot UsedGREEN/WHITE - GroundBLUE - (-) Boot Input - Zo

www.directed.com56WHITE/BLACK - Lock 87A (Normally Closed)GREEN/BLACK - Lock 30 (Common)VIOLET - Unlock 87 (Normally Open)BROWN/BLACK - Unlock 87A (No

© 2007 directed electronics57notes____________________________________________________________________________________________________________________

www.directed.com4transmitter configurationsThe Concept 650MkIIsystem has two 5-button remote controls. Two additional remotecontrols can be added.1. L

www.directed.com58

© 2007 directed electronics5standard configurationButtonThe arming and disarming functions are controlled by this button.ButtonThe boot release or acc

www.directed.com6primary harness wire connection guideprimary harness wiring diagram______________________________________________________BLACK/WHITE

© 2007 directed electronics7primary harness wiring guideThis guide describes in detail the connection of each wire. Also included are possibleapplicat